Search results

Has anyone fitted these? I am looking at buying the spoon ones for my front x member as I can't get my alignment right! (No crash damage/ anything bent etc) but I can only get more camber on one wheel than the other (using camber bolts), and it would make sense that my subframe is offset one...

I have the same rear as you, and mine only gets a handful if really hammering! (And i don't hang about).

It's the front pal. Get it set to zero and try that.

Haha no where near me! I'm in Nottingham 🙄

Sorry, just read your post and you already have upgraded bushes. This in my experience won't affect tramlining, so i doubt it's that, but any play in the steering will, as well as certain tyre tread patterns. From the sound of it it's down to the toe. Worth going to any tyre place and ask...

My next job is polybushing the front end as my tca bushes are perishing, as i can feel the car being pulled about from the uneven road surface. Only slightly, but its there. With worn bushes, the wheels will get pulled about. Worth a look!

Oh and for anyone searching the thread looking for an answer to my pulling whilst accelerating/ decelerating, fitting new ad08r's solved it. Vanished instantly! Although it has thrown my steering wheel off centre by a few degrees?! Just got to sort out my lack of front camber, then have the...

It would be worth asking him what your toe is set to, i had a fast road setup on my fn2, with toe out and although it turned in quick, it was awful on a back lane, it took real concentration to keep it in my lane! Fast forward to buying the teg, and when i had my geo setup, i asked for zero...

I had my geo setup, and the handling is so much better (might be due to the fact it had positive camber on the front right wheel!) But with eibach camber bolts he could only go 20mins neg on one side, and half a degree on the other!? That's the max he could go with the bolts? So he evened them...

Hello guys, i am currently trying to wire my inner brake lights to fog lights for the mot next week, i have used the search function but all the links are dead. From what i have read, i need a diode somewhere in the wiring, but can't figure out where? I have wired a switch from ignition...

I rang my local Honda dealer, £420, used one it is then...

Before you ask, i have just spent nearly half an hour using the search function! My handbrake light is on permanently, i have looked at the wiring diagram in the manual, and as far as i can see the only two things that can light this is the handbrake switch and the brake fluid sensor, which both...

I have figured it all out now, they are a really good bit of kit! Installed all my cds on the internal drive, renamed them in English etc. loads of adjustments with the sound, plays movies etc. I used Google translate and spent an hour or two playing about.

any news on your pulling to the right? Mine is doing exactly the same and its going on Friday for an alignment, hopefully that will cure it!

I am taking my car to be aligned next Friday, and i have a quick question, i have done loads of research on the setup i want, but i am not sure on the rear toe in, 2mm seems to be popular, is that total over the rear wheels? And why is the rear not measured in degrees but in mm? Thanks.

I am taking my car to be aligned next Friday, and i have a quick question, i have done loads of research on the setup i want, but i am not sure on the rear toe in, 2mm seems to be popular, is that total over the rear wheels? And why is the rear not measured in degrees but in mm? Thanks.

I am going in for a geo setup in the next few weeks so i will report back on the results! I have a sneaky suspicion that the eibach springs have been fitted without having an alignment done! Going for -1.8 camber front, 0 toe front, -1 camber rear with 2mm toe in.

I am looking at fitting my toad ai606 alarm i had on a previous car to my teg, but i need to remove the original Honda one. Could anyone help via pm on where its located and how its wired in? And if anyone has a data sheet for the dc5 regarding wiring the toad in that would be great! i Would...

What about a mugen twin loop? I have one and its quiet, even with a spoon manifold, but i don't see many people on here mention them/recommend them?

Cheers lads that's my birthday present sorted!